What’s The Ideal Way To Clean A Rug?
Area rugs are a excellent way to add warmth and character to your decor, but after prolonged use, they will require a good cleaning to look like brand new. For most modern rugs, cleaning can be a once-a-year DIY job that saves you the cost of specialist cleaning. If your rug is tagged with particular cleaning instructions, follow these.
In general, area rugs only need to be deep cleaned annually. Listed below are a Couple of ways to determine If It’s time for Rug Cleaning in North Hills:
1. Lift a corner of the rug and lightly kick the back. If the rug releases a large cloud of dust, it definitely needs some attention.
2. Run your hand against the rug face in a circular motion for 10 seconds, then look at your palm; if your hand is dirty, then so is the rug.
3. Check for signs of deeply embedded dirt by looking at the rug backing. Deep-down dirt will settle along the warp and weft of the rug and can be seen in the backing.
Cleaning a rug just requires a few basic tools. You may need:
Rug beater or broom
Rug shampoo or safe cleaning solution
Two 5 gallon buckets
Large sponges
Towels
Large tarp
Fan
Prior to cleaning a rug, read the care instructions on the rug’s label. Try to pick a time to clean your rugs when there will be a few glowing, hot days together. It may be a lot easier to clean your rugs outside, and sun and warm air will help them dry more quickly and thoroughly. Additionally, the sun is a natural and effective deodorizer and this will keep most of the dirt and dust from the home. Whether an outdoor area isn’t available, use any floor area which moisture won’t damage (like concrete or vinyl flooring in the kitchen or garage.)
Shake or conquer Require smaller rugs and darkened rugs outdoors and give them a fantastic shake to release loose dirt and dust. If the rug is large, ask a partner for assistance to hang the rug above a porch rail or above a couple solid chairs. Do not forget to shake the rug mat also.
Mix the cleaner: Create a cleaning solution as directed by your chosen rug shampoo, or blend two to three teaspoons of mild dish soap to one of the 5-gallon buckets with warm water. Fill another bucket with clean water.
Test the rug for colorfastness: Prior to cleaning a rug with any kind of solution, it needs to be tested for colorfastness to prevent harm. Dab the cleaning solution on a small corner of this rug with a towel. Allow the test spot dry completely, then check again to make certain colors have not bled or faded.
Scrub, if necessary: When the rug is colorfast, put on the soap solution to the rug with a soft-bristle brush or sponge. Start at one end of the rug. Dip the sponge/brush to the cleaning solution. Don’t over-wet the fibers–only use as much as required. Function in a 3- by 3-foot location. Rinse out the sponge/brush frequently so the dirt won’t be transferred.
Scrub the rug thoroughly: It is important not to leave any soap material on the rug. Soap will attract more dirt. Dip a clean sponge at the rinse water and remove any soap from the area just cleaned.
Blot: Push out as much excess water as you can using a squeegee and moving from the path of this rug nap. Scrub, rinse and blot a place before moving to the next.
Dry: Hang up the rug to dry, or put the rug level, face-up and prop the bottom with risers to allow for air circulation. Allow the rug dry thoroughly prior to bringing it back inside, rotating it occasionally to promote even drying. Once inside, turn on fans to promote more air circulation and assist the rug dry more completely.
Adjust rug fibers: When the rug has dried completely, lightly go over the rug using a vacuum or a soft-bristle brush to Blend the fibers.
Steam cleaners: If your rug is extremely soiled, it may be well worth it to let a commercial steam cleaner. Vacuum the rug first, then follow the manufacturer’s directions about how best to operate the machine.
Check related blogs about Rug Cleaning:
Is It Worth Getting Carpets Professionally Cleaned in North Hills
